GHOST RC - 1412 SENSORED MOTOR - 4300kv DRAG MOTOR
Product #: 060-0119-00
Castle is excited to partner with Ghost RC in offering high performance electronics for the RC Sand Drag Racing market. Ghost RC products are designed and made by Castle to Ghosts requirements based on the extreme demands on RC drag racing. Upgrade your racing experience with the Ghost RC1412-4300kv motor with adjustable endbell and unleash its power and speed for exhilarating sand drag racing performance.
SUPPORT: Castle Creations does not provide technical support or service on Ghost RC products, nor does Castle offer trade-ins for this product as it is not a Castle product. Please contact Ghost RC for any questions regarding their products.
WARRANTY: Due to the abusive nature of drag and speed run setups, Castle nor Ghost RC is liable for incidental or consequential damages to other equipment such as ESCs and batteries when using this motor and is not responsible for failures resulting from abuse, improper installation, misapplication or alteration. This product is for advanced users in drag racing applications. Due to the aggressive and abusive nature of drag racing, this product is sold with no warranty.
WARNING: Drag and speed run setups are inherently abusive and extremely hard on all electronic components. Every component in the configuration can be strained, weakened (or worse) without using extreme caution, observance of electric theory and advanced knowledge of all aspects of the RC hobby. High speed runs and drag racing are the most advanced, aggressive and volatile applications in the RC car hobby. Improper setup or use of this product can result in catastrophic failures of the motor, ESC and/or batteries.
FEATURES:
- Stainless-wrapped rotor
- Ensures durability and reliability, allowing for high-speed operation.
- With a maximum RPM of 90,000, this motor is built to handle extreme racing conditions.
- 550-sized can, the motor is compact and lightweight.
- 5mm output shaft
- Siamese flats provides a secure and durable platform for your 48p or 32p pinions.
- Compatible with 2-4s batteries.
- Adjustable rear endbell
- Allows timing adjustments from 0° - 40°
- Oversized solder tabs and motor wires
- Large 8 gauge wire to handle the high demands on drag racing
- Beefy solder tabs to reduce resistance and increase current capacity
| Technical Specs | |
|---|---|
| Input Voltage Range: | 2s-4s LiPo |
| Kv: | 4300 |
| Max. RPM: | 90,000 |
| Size: | Length: 68.2mm Diameter: 36mm |
| Weight (w/wires): | 325g (11.4oz) |
| Shaft Size: | Length: 20mm Diameter: 5mm |
| Mounting Hole Specifications: | M3 @ 25.4mm |
| Cooling Fan: | Optional |
| Connectors: | 6.5mm male Castle Bullet Connectors attached to replaceable 10 gauge wire |
| Items Needed for Operation: | Compatible Electronic Speed Control (ESC) |
| Application Guidelines: | For 1/10th scale No Prep Drag Cars |
| Recommended ESC(s): | Ghost RC Cobra 8 ACE |
| Running Modes: | SmartSense™ (with Castle Sensor capable ESC), Sensored and an ultra-efficient Sensorless mode. |
| Tech Notes: | Water Resistant Design: The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommended applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to this document for running and maintaining motors in wet environments. |
This is ahigh power product with the potential to be very dangerous. Please read the safety information before use. This product may contain chemicals known to the State of California to cause cancer and or birth defects or other reproductive harm.
Motor designed in Olathe, Kansas USA.
Motor manufactured in China.
| Resources |
|---|
| Sensored Motor Quick Start |