Telemetry Link for Spektrum X-BUS
Product #: 010-0148-00
Knowledge is Power!
Maybe you want to know the voltage of your onboard battery(s), the RPM the motor is turning or the temperature of your ESC. In this day and age R/C is not just one way communication anymore. Traditional radio systems transmit signals from the controller to the receiver, but Telemetry-capable systems also send real-time data from your model back to your transmitter. The X-BUS Telemetry Link was developed based on communication protocol disclosed from Spektrum® for use with specific Spektrum® radios and compatible Castle Creations ESC’s. Telemetry data can be displayed on the transmitter screen, or notify you when a defined threshold is exceeded, (battery voltage, ESC temperature, etc.) you can configure a vibration or sound alert from the radio. Let’s start from the beginning.
Why should I integrate Telemetry into my models?
Telemetry has the potential not only to improve the safety of our models by monitoring battery voltages, ESC temperature, and other critical parameters, but it also creates other opportunities to get even more fun out of flying because it essentially reduces the risk of “unknown” inevitable crashes. Think of the benefits to be had from alarms that will sound to warn you if your ESC is running hot or if your receiver battery is running unexpectedly low.
- Availability: Note-This item is out of stock and will be backordered.
|Compatible Castle ESC||The ESC must have the ability to accept a bi-directional communication protocol that gives it the ability to transmit real-time telemetry feedback. This feature is called Link Live™ and needs to be enabled on compatible ESCs using Castle Link™. Click here to view the Castle ESC Compatibility Chart.
Note: The Telemetry Link will not work if the ESC is programmed for Multirotor or External Governor Mode due to the higher PWM frequency.
|Compatible Spektrum X-BUS Radio||These selected radio’s support bidirectional communication. It is also necessary to utilize a compatible Spektrum Telemetry Module. Click here to view the Spektrum® Radio Compatibility Chart.|
Now, let’s see the mechanical integration.
Below is an example of an X-BUS Telemetry Link set-up for Surface, Air and Internal Governor Systems. You can see how the Telemetry Link (about 5.4 inches long) connection is made between the Castle ESC and the Spektrum® X-Bus™ receiver and Telemetry Module/System.
And how about this….there is no requirement for additional Telemetry Sensors for your Spektrum® radio when using the X-BUS Telemetry Link. There are 7 specific data points available* and you can enable/disable to your liking through Castle Link™.
Note: data points available may vary depending on the ESC's capabilities.
|Spektrum® X-Bus Telemetry Link Data Points|
|Battery Voltage||You will be able to see the voltage state of your battery during flight and respond appropriately to deteriorating conditions or alarms you’ve programmed in your radio.|
|Battery Current||Compatible controllers will transmit the instantaneous current draw of the system. You can use this information to reduce the load to prevent an over-current shutdown.|
|Motor Power Output||This is the percentage of full power your ESC is delivering to your motor.|
|RPM||Ensure you are within acceptable parameters, without the use of a tachometer.|
|BEC Voltage||Monitor your BEC voltage and its stability to the RX even under different loads from different servos.|
|ESC Temperature||ESC temperature monitoring can eliminate a potential thermal shut down.|
Operation of a model aircraft requires your undivided attention. We encourage you to refer to your transmitter manual to configure tactile and/or audible alerts to ensure your safety, and the safety of those around you.
Have confidence in pushing your model to its limits.
Let’s face it, your time and your energy should be devoted to enjoying your craft. Telemetry adds a whole new aspect to the RC pilot or driver that, when set-up and utilized properly, can take a lot of work load away and add to the overall satisfaction and safe operation of model airplanes, helicopters and cars.
You can review compatible radio systems and much more on the X-BUS Resource page.
|Size:||Circuit board: 1.0" (25.4mm) x 0.44" (11mm)
Overall dimensions: 5.25" (133mm) x 0.44" (11mm) including wires
|Weight:||0.192 oz (5.44g) without wires|
|Tech Notes||The Telemetry Link will not work if the ESC is programmed for Multirotor or External Governor Mode due to the higher PWM frequency.
The maximum RPM is limited to 100,000 electrical RPM (Calculated by multiplying mechanical RPM by half of the magnetic poles)
The Telemetry Link cannot be used in conjunction with the the B-Link Bluetooth adapter.
|Telemetry Link for Spectrum X-Bus User Guide|
Castle Creations, Inc. warrants this product to be free from manufacturing defects for a period of one year from date of purchase.
Product designed, and circuit boards manufactured, in Olathe, Kansas USA.
Product assembled in Mexico.